Auto Paintless Body Dent Removal Kits Car Dent Repair Tools Automotive Dent Remover Suction Cup Dent Puller Tool Kit for Car

Description

Material: Plastics+Stainless steel (not full metal)
​
Features:
​Made of fine quality material, long-lasting to use.
​Can help you repair the dents on your car.
​It will not harm the painted surfaces.
​Suitable for the sheet metal processing of automobile, refrigerator, motorcycle, washing machine, etc.
​
​【Kit 1】
​Package included:
​20x Blue Tabs
​1x Gold Puller
​2x Shovel
​1x Towel
​1x The Instruction
​
​【Kit 2】
​Package included:
​1x Hammer
​10x Knocking pen
​
​【Kit 3】
​Package included:
​7 x Pulling bridge set
​
​【Kit 4-58Pcs】
​Package included:
​12x Red Tabs
​28x Blue Tabs
​1x Gold Puller
​2x Shovel
​1x Glue Gun(US/EU Plug,20W)
​5x White Glue Sticker(7*270mm)
​5x Yellow Glue Sticks(7*270mm)
​1x Towel
​1x Alcohol Bottle(Alcohol not included)
​1x Tools bag
​1x The Instruction
​
​【Kit 5-76Pcs】
​Package included:
​12x Red Tabs
​28x Blue Tabs
​1x Gold Puller
​2x Shovel
​1x Glue Gun(US/EU Plug,20W)
​5x White Glue Sticker(7*270mm)
​5x Yellow Glue Sticks(7*270mm)
​1x Towel
​1x Alcohol Bottle(Alcohol not included)
​1x Hammer
​10x Knocking pen
​1x Tools bag
​1x The Instruction
​7 x Pulling bridge set
​
​How to use the tools ?
​1. Clean damage surface with a clean wet cloth;
​2. Put the glue stick to gun and connect the power source and preheat for 5-10 minutes;
​3. Pull the trigger and apply the suitable drawing gasket with extruded glue (The 4 holes of gasket should be applied with hot melt glue);)(Note: The larger the drawing gasket is, the larger the drawing force is);
​4. Immediately place the drawing gasket with hot melt glue in the center of the dent and hold until sticks (Let the glue cool for about 5-8 minutes. The cooling time should be less than 10 minutes and should be shorter slightly in winter);
​5. Align the T-shaped repairer and press the drawing gasket with hot melt glue, pull the sliding rod backwards to pull up the dent;
​6. When dent was removal, clear the glue by alcohol with plastic shovel;
7. If dent still exists, knock it slightly with a flattening hammer with Tapdown head
​8.Repeat the operation steps above until the dents are repaired.

Question 1: The glue is not strong, the glue is debonded, what is the reason?
1. The viscosity of hot melt adhesive is related to the temperature. The ideal temperature is 20°C-28°C.
Note: Do not operate under the sun in summer, and the operating temperature in winter is above 10 ℃ (if the weather is very cold, you can first pour hot water on the wagon in the recess)
2. If the car has been waxed or plated with crystal film or the material of the recess is not iron sheet, the stickiness of the tape will be greatly affected.
3. It may be that the product is dusty during use. Before use, it is best to use alcohol to clean the rubber strip, the dent surface and the gasket.
4. If it is degummed during operation at ideal temperature, this is a normal phenomenon, and it only needs to repeat the operation.
If the depression cannot be repaired after repeated operations, it may be that the puller is not suitable for processing the depression. This is related to the shape, position and size of the depression. Not all depressions can be repaired with one product, which has nothing to do with the glue.

Question 2: How to remove the glue
You can use alcohol above 95 degrees, while tearing it again and spraying alcohol, the residual glue can be buttoned off with your fingernails. Asphalt, gasoline or diesel can also be used.
(Because alcohol is flammable and cannot be transported, please buy it locally. Sorry for the inconvenience caused.)

Note:
1. It is not recommended to use if the body has been waxed, there is a car coat, a film has been coated, or the paint surface is cracked.
2. The dent is not a metal sheet, or the dent is in a particularly hard place such as the body beam and cannot be repaired with tools.